Interview Questions with Answers


1. What is priming?
- Pump casing must be filled with liquid before the pump is started, or the pump will not be able to function. If the pump casing becomes filled with vapors or gases, the pump impeller becomes gas-bound and incapable of pumping.
2. Types of pumps?
- Positive Displacement
       - rotary lobe pump, progressive cavity pump, rotary gear pump, piston pump, diaphragm pump, screw pump, gear pump, Hydraulic pump, vane pump
- Centrifugal Pumps
        - end suction pumps, in-line pumps, double suction pumps, vertical multistage pumps, horizontal multistage pumps, submersible pumps, self-priming pumps, axial-flow pumps, regenerative pumps.
3. What is octane number in fuel?
- The octane rating of Gasoline is measured in a test engine, and is defined by comparison with the mixture of 2,2,4-trimethylpentane (iso-octane) and heptane which would have the same anti-knocking capacity as the fuel under test: the percentage, by volume, of 2,2,4-trimethylpentane in that mixture is the octane number of the fuel. For example, petrol with the same knocking characteristics as a mixture of 90% iso-octane and 10% heptane would have an octane rating of 90.
4. What is added in LPG to detect leakage?
- Methyl Mercaptan 
5. Pascal law ? Applications?
- Pascal's law or the Principle of transmission of fluid-pressure states that "pressure exerted anywhere in a confined incompressible fluid is transmitted equally in all directions throughout the fluid such that the pressure ratio (initial difference) remains the same.
Application- Hydraulic jacks, Car lifts, Fork Lifts
6. Can you transfer the heat energy from cold body to hot body?
- Yes, with external work. Eg : Air conditioner
7. What is hogging and sagging?
- Hogging and sagging describe the shape of a beam or similar long object when loading is applied. Hogging describes a beam which curves upwards in the middle, and sagging describes a beam which curves downwards.


8. What Bernoulli’s Principle?
- In fluid dynamics, Bernoulli's principle states that for an inviscid flow, an increase in the speed of the fluid occurs simultaneously with a decrease in pressure or a decrease in the fluid's potential energy.


9. Difference between single acting and double acting pump?
- In single-acting machines the compression takes place on only one side of the piston; double-acting machines use both sides of the cylinder for compression. The flow is continuous in double acting and in single acting the flow is not continuous unless there is a surge vessel.
10. What is VSD?
- Variable Speed Drive
11. What is conduction, convection and radiation? Give Examples?
- Conduction or diffusion
The transfer of energy between objects that are in physical contact
Convection
The transfer of energy between an object and its environment, due to circular fluid motion

Radiation
The transfer of energy to or from a body by means of the emission or absorption of electromagnetic radiation

12. Mention flow measuring devices?
- Venturimeter, Rotameter etc.
13. Classify Carbon Steels on basis of carbon content?
Low-carbon steels contain up to 0.30% C. The largest category of this class of steel is flat-rolled products (sheet or strip), usually in the cold-rolled and annealed condition. The carbon content for these high-formability steels is very low, less than 0.10% C, with up to 0.4% Mn. Typical uses are in automobile body panels, tin plate, and wire products.
For rolled steel structural plates and sections, the carbon content may be increased to approximately 0.30%, with higher manganese content up to 1.5%. These materials may be used for stampings, forgings, seamless tubes, and boiler plate.
Medium-carbon steels are similar to low-carbon steels except that the carbon ranges from 0.30 to 0.60% and the manganese from 0.60 to 1.65%. Increasing the carbon content to approximately 0.5% with an accompanying increase in manganese allows medium carbon steels to be used in the quenched and tempered condition. The uses of medium carbon-manganese steels include shafts, axles, gears, crankshafts, couplings and forgings. Steels in the 0.40 to 0.60% C range are also used for rails, railway wheels and rail axles.
High-carbon steels contain from 0.60 to 1.00% C with manganese contents ranging from 0.30 to 0.90%. High-carbon steels are used for spring materials and high-strength wires.
Ultrahigh-carbon steels are experimental alloys containing 1.25 to 2.0% C. These steels are thermomechanically processed to produce microstructures that consist of ultrafine, equiaxed grains of spherical, discontinuous proeutectoid carbide particles.

14. Draw a possible isometric view for the object that has the following plan and elevation views?
 

18 comments:

vergarasofia197@gmail.com said...

Tks very much for your post.

Avoid surprises — interviews need preparation. Some questions come up time and time again — usually about you, your experience and the job itself. We've gathered together the most common questions so you can get your preparation off to a flying start.

You also find all interview questions at link at the end of this post.

Source: Interview Questions & Answers:

Best rgs

Mustafa king said...

Please visit this link you find amzing and new collection of whatsapp status



Top Hindi Whatsapp

Top 100 Cool whatsapp status

Top 100 Romantic whastapp status

Top 50 Sad whatsapp

Romanitc status

Miss u status

Attitude status

Motivational Status

Birthday Status 

Friendship Status

Sad Status

joecoles222 said...

Tks very much for your post.

Avoid surprises — interviews need preparation. Some questions come up time and time again — usually about you, your experience and the job itself. We've gathered together the most common questions so you can get your preparation off to a flying start.

You also find all interview questions at link at the end of this post.

Source: Download Ebook: Ultimate Guide To Job Interview Questions Answers:

Best rgs

Interview questions answers pdf said...

Latest Mechanical Engineering Interview Questions and Answers
http://allinterviewquestionsandanswerspdf.blogspot.in/2016/06/top-100-mechanical-engineering.html

Mahaveer cooling towers said...

We manufacture wide range of PVC Eliminator, PVC Nozzles and hollow frp fans. We make all types of cooling towers that fulfil the requirements of our innumerable clients.

PVC Eliminator manufacturers

PVC Nozzles manufacturers

Hollow frp fans manufacture

FRP Cooling Tower

Water cooling towers manufacturers

Cooling tower manufacturers in India

Wooden cooling tower manufacturers

Timber Cooling Tower manufacturers



Jagan Jai said...

Nice to see this event more surprise of new technology used your service. We are servicing aluminium scaffolding manufacturing you need this product kindly contact www.sendhamarai.com

Pradeep Singh said...

Great Opportunity for my business modular kitchen In Chennai & Modular Kitchen in Chennai. I need support to approval the comment some people view our business.

Yajnarup said...



This post will be very useful to us....i like your blog and helpful to me....nice thoughts for your great work..

FRP Tank Manufacturers in Chennai

Pradeep Singh said...

The designs work is great in app see more excellent modular kitchen dealer in chennai in google app. Keep watch and check the chennai reviews.

Canara Hydraulics said...


This is such a great resource that you are providing and you give it away for free. I love seeing blog that understand the value of providing a quality resource for free Hydraulic Power Pack Manufacturers in India | Helical Rotary Actuator

Aby Saxen said...
This comment has been removed by the author.
Aby Saxen said...

Have you interested to know how mechanical activity transforming Oil and Gas Industry ? Reach out Oges.info to know how it does and about opportunity in Oil industry. Ask you query & get answer by Oil and Gas mavens. https://oges.info/dashboard

Engineer's Chaupal said...

This concept is a good way to enhance thes knowledge. Thank you and keep it.
best engineering Suppliers in india
Engineering Portal in india
best engineering Suppliers in india

sumathi s said...

I wish to show thanks to you just for bailing me out of this particular trouble. As a result of checking through the net and meeting techniques that were not productive, I thought my life was done.
fire and safety training in chennai

Swetha Gauri said...

You rock particularly for the high caliber and results-arranged offer assistance. I won't reconsider to embrace your blog entry to anyone who needs and needs bolster about this region.
Occupational health and safety course in chennai

Hydrauliques Continental said...

Informative blog ,.! I really loved reading through this article... Thanks for sharing such an amazing post with us and keep blogging! Hydraulic Pump Repair

Aswathi said...

Nice sort of questions.If you are interested with hydraulic jobs,then I would like to recommend you the site Whyps .Here you can find everything related to hydraulics such as hydraulic jobs,hydraulic career, hydraulic industry trends, Hydraulic videos, hydraulic projects, new projects in hydraulics industry, hydraulic research, Hydraulic Industry Articles , hydraulic exhibition, hydraulics society, hydraulic conference, hydraulic seminars, basic Hydraulic Training , hydraulics trade shows, hydraulics books, hydraulics magazine, hydraulics training, hydraulics courses, hydraulics training institutes and many more.

Ekeeda said...

Your website is very beautiful or Articles. I love it thank you for sharing for everyone. Basic Electrical Engineering Videos